Skip to content

Commercial gate and access control service in Western New York

Control Services of WNY installs, repairs, and maintains automatic gates, gate operators, access control, and security camera systems for commercial properties in Buffalo, Niagara Falls, and across Western New York. The region sits at the western end of the Albany-to-Buffalo corridor the company works regularly, and calls get a callback within the hour, 24/7.

Built for the lake-effect snow belt

Snow off Lake Erie can arrive in narrow, heavy bands that bury one part of the region and miss the next. At a gate, that means drifts packed into slide gate tracks, swing gates that cannot clear their arc, and safety sensors covered over.

An operator pushing against packed snow works its motor and drive hard on every cycle. Equipment sized for the gate and the conditions, with controls protected from the weather, is what gets a commercial entry through a Buffalo winter.

What a Buffalo winter does to an entry

Most winter service calls in the region come back to a few causes. Each one is easier to prevent than to repair in February.

Plow and truck hits

Vehicles hitting the gate or a peripheral device is the most common cause of failure anywhere. Snowbanks narrow the entrance and leave plows and trucks less room around posts and keypad pedestals.

Packed snow and ice

Ice in tracks, hinges, and the gate's travel path makes the operator strain and can stop the gate partway.

Road salt and slush

Salt spray reaches low hardware, pedestals, and the base of the operator, which is where corrosion starts.

Melt and refreeze

Water from a thaw works into housings, connections, and conduit, then freezes there overnight.

Storm outages

When a winter storm takes the power, how the gate behaves depends on the power setup and backup planned for it.

Wind off the lake

Wind loads a large gate panel and pushes snow into the same corners of an entrance storm after storm.

Commercial sites around Buffalo and Niagara

Across Erie and Niagara counties, the properties that rely on a working gate include storage facilities, manufacturing plants, warehouses and distribution yards, apartment complexes, and corporate campuses.

With the Canadian border crossings close by, many yards in the region see steady truck traffic. When the gate at one of those sites goes down, shipments wait at the entrance until it is fixed.

Maintenance timed to the seasons

Preventive maintenance visits in spring and fall, up to four a year for high-security sites, are the best defense against a midwinter breakdown. Scheduling one visit before the snow and one after salt season lines up with how Western New York wears equipment down.

A professionally installed and maintained system can last around 10 years, depending on how many times the gate cycles each day.

When the gate is down today

Send a request with the brand, what the gate is doing, and a few photos. That tells the technician what to bring so the first visit can be the fix.

Technicians work on HySecurity, Magnetic Autocontrol, DoorKing, LiftMaster, FAAC, Viking, and other professional-grade operators, along with the loops, keypads, and readers tied to them.

Western New York service questions

How soon can you get to a gate in the Buffalo area?

Western New York is part of the Albany-to-Buffalo corridor the company works regularly. Call and you'll hear back within the hour, 24/7. Commercial accounts with critical sites can set up a service agreement for on-site response in as little as 4 hours. Include photos with your request.

Do you serve Niagara Falls and the Buffalo suburbs?

Yes. The Western New York service area covers Buffalo, Niagara Falls, and the surrounding communities in Erie and Niagara counties.

Can a gate operator keep up with lake-effect snow?

A professional-grade operator sized for the gate, installed with protected controls, and kept on a maintenance schedule is built to run through winter. Packed snow and ice in the gate's path still need to be cleared, because an operator should never be forced through them.

What does road salt do to gate equipment?

Salt corrodes metal hardware, posts, and the base of operators and keypad pedestals over time. Preventive maintenance visits catch that corrosion before it weakens parts or reaches the electronics.

Planning a new system, or need service on one you have?

New gates, access control, and cameras start with a site survey. Gate or system down? Call us and you'll hear back within the hour. We're available 24/7.